|
|
Post by capemayal on Sept 24, 2021 12:09:10 GMT -5
18380 FLF five slides front two slides okay rear three slides on one switch. One bedroom slide comes in, The other bed slide and the kitchen slide do not come in. Kitchen and the one bedroom slide are on the same side. I have to get moving and don't know what to do. I'll tried everything I can. Reset the controllers. Disconnected the motors at the controller. But nothing happens with those two slides any help appreciate it
|
|
luscombet8f
Weekender RV’er
My 1949 Luscombe T8-F & 251RLT
Posts: 68
|
Post by luscombet8f on Sept 27, 2021 9:35:10 GMT -5
I am hoping you get some suggestions... I'm no help.. but my 2017 251RLT with 3 slides has some manual inputs (which I have never needed). I have rigged up some tooling should that happen... Some day I'll see what I can learn about the forward closet slide... haven't investigated that one yet. Good luck with yours...
|
|
Nomad
Newbie RV’er
Posts: 41 
|
Post by Nomad on Sept 28, 2021 9:56:41 GMT -5
Did you check the fuses at the controller and motor points? Usually BIG Green ones
|
|
|
|
Post by termy251 on Sept 29, 2021 7:35:36 GMT -5
I had an issue last time out with my slide. I found the LED lights in the slide would not come on. Thought not a big deal about the lights, but when I went to close up, the slide would not come in. I gather they are on the same power. So, I kind of messed around with the (lack of better term), stretchy cord under the slide. Pushed on all the connections and the lights came back on and the slide went in.
Could be a connection that is loose under the slide on your unit. 326RLT is my unit. Good luck.
|
|
|
|
Post by capemayal on Sept 29, 2021 12:24:45 GMT -5
18380 FLF five slides front two slides okay rear three slides on one switch. One bedroom slide comes in, The other bed slide and the kitchen slide do not come in. Kitchen and the one bedroom slide are on the same side. I have to get moving and don't know what to do. I'll tried everything I can. Reset the controllers. Disconnected the motors at the controller. But nothing happens with those two slides any help appreciate it Got to the bottom of it. I was at a non-KZ dealer, not that it would have mattered, hooked to a 30A outlet. Had plenty of ATF in the reservoir. At the park where I am staying, I had to switch to 30A because the 50A dropped a lug. Called Lippert and the tech had me check the slide's solenoid valve and coil. The dealer's tech talked to them too, when they came to continue trouble shooting - about 930am. Got 12v there. They worked until closing at 5pm, and gave up. They did try a used one they "had lying around", no joy. So, says them, it must be a bad valve/wire, which they'll have to replace, but can't have it for at least a week! That night I'm racking my brains out. What did I miss? Really racking it out - 20 years, and can't figure it out. Finally realized I had a 30A dog-bone on the dealer's 30A outlet. Just too lazy to take it off and plug into the 50A, but I was only supposed to stay overnight. Well, that evening I knew I had checked my fuses, breakers, etc. But, the Only thing I didn't check was the pole! Unplugged, removed the dog-bone and plugged into their 50A. VIOLA! Everything is OK! So, I told their service manager they had low voltage on the 30A. Oh, no, says he! Can't be. Well, I left them to figure out, as I waved when I pulled out 10 minutes later. So, like I've done over the last 20 years. Check the pole voltage BEFORE you plug in! This dealer's facilities left a lot to be desired, though. Everyone, including Lippert and the dealer's techs wanted to ONLY look for the hardest most expensive thing, just like me, DUH! So that dealer, in the future - Stewart's Mobile Village, Avon Park, FL, is a "no go back to for me". |
|
